obd2shop

ponedjeljak, 28.02.2022.

Yanhua Mini ACDP + Module 13 Clone VW Audi DQ200/250 Gearbox

Yanhua Mini ACDP + Module 13 is supported to clone VW(Volkswagen), Audi DQ200(0AM/0CW), DQ250(02E/0D9), DL382(0CK), DL501(0B5), VL381(0AW) models, etc. Here is taking Audi DQ200 & DQ250 gearbox clone as demonstration.

Check our Youtube:
https://www.youtube.com/watch?v=1EC5RhfzF40

VW Audi DQ250 Gearbox Clone
Click “Help” to find connection info.
Required Accessories:
DQ250 module
OBP+ICP adapter
ACDP host
DQ250 interface board
20PIN cable

Connection
1.Install DQ250 interface board.
2.Short circuit the CAN resistor on PTCU adapter to the “CAN-R” JOIN side.
3.Connect OBP+ICP adapter, interface board & ACDP host.

Operation
Mini ACDP >> VW >> Gearbox clone >> Audi >> Confirm model & SN >> DQ250(02E/0D9) >> Full backup
Follow the instruction, then click “OK”.
1.Connect ACDP with Gearbox.
2.This function needs to be connected to the Internet. Make sure the network is good.

Confirm the gearbox model, continue >> OK
Backup file succeeded(record its filename & location).
OK >> OK

Connect another DQ250 gearbox & prepare to write the original data.
Full write >> OK >> Continue >> OK >> Select the backup data saved before
Writing PFLASH data...
Writing EEPROM data...
Data wrote successfully!

VW Audi DQ200 Gearbox Clone
Click “Help” to find connection info.
Required Accessories:
DQ200 module
OBP+ICP adapter
ACDP host
DQ200 interface board
20PIN cable

Connection
1.Install DQ200 interface board.
2.Short circuit the CAN resistor on the PTCU adapter to the “CAN-R” JOIN side.
3.Connect OBR+ICP adapter, interface board & ACDP host.

Operation
Mini ACDP >> VW >> Gearbox clone >> Audi >> Confirm model & SN >> DQ200(0AM/0CW) >> DQ200Dxx/DQ200_MQB (Choose depend on SN, check Help) >> Full backup
1.Connect ACDP with Gearbox.
2.This function needs to be connected to the Internet. Make sure the network is good.
Confirm model, continue >> OK >> OK
Backup file succeeded.
Please record the file name & location.

Connect another DQ200 gearbox & prepare to write the original data.
Full write >> Follow the instruction, OK >> Confirm model, continue >> Select the backup data saved just now
Writing PFLASH data...
Writing EEPROM data...
Data wrote successfully!

The Yanhua ACDP Module 13 has replaced the traditional wire method to be more simple & efficient. Plug & play to support Seat, Skoda as well.
www.obd2shop.co.uk

Oznake: yanhua acdp, yanhua mini acdp

28.02.2022. u 04:05 • 0 Komentara • Print • # • ^

nedjelja, 27.02.2022.

Autel Tablets How to send DataLog from History

How to send the data log after disconnecting from the vehicle and running a function error on AUTEL tablets?

Here is the guide that helps you:

Find and enter the Data Manager

Click Data logging

Select "History" on the "Data logging" interface
Click "right arrow" to the corresponding function page to submit the log

Fill in the reason and submit

For further technical support, please contact
https://www.obd2shop.co.uk/

Oznake: Autel

27.02.2022. u 03:59 • 0 Komentara • Print • # • ^

subota, 26.02.2022.

(Fixed) Launch X431 V renewal card was not found during the update

Customer program: After Launch X431 V 8 inch update, the renewal card cannot be found, just like the picture shows

Solution: The engineers at Obd2shop.co.uk checked the customer's image and X431 SN, found that his X431 V update has expired so the Renewal card cannot be displayed.

If you need to upgrade X431 V series products as well, you can buy:

1 year upgrade subscription:
https://www.obd2shop.co.uk//1-years-update-service-for-launch-v-pro-mini-diagun-iv.html

2-year upgrade subscription:
https://www.obd2shop.co.uk//2-years-update-service-for-launch-v-pro-mini-diagun-iv.html

Oznake: launch, Launch X431

26.02.2022. u 14:12 • 0 Komentara • Print • # • ^

četvrtak, 24.02.2022.

(Fixed) Godiag GD201 enters PlayBack function and the white screen appears

Customer question: A white screen appears when I use my Godiag GD201 to access the PlayBack function key, what should I do?

Answer: Need to update the operating system.

The specific steps are below or you can watch the video on YouTube:
https://youtu.be/MO5klRnZ0RM
Use the USB cable to connect GD201 and the computer

Open your browser, enter the URL "www.godiag.com" to download the upgrade kit

After downloading, extract the update tool and installed it on your desktop

Open Godiag updater, click on "register" to register (if you are already registered, you can directly enter your account number and password to log in)

Fill in the information to complete the registration, then log in

After logging in, you can see the following information on the "My Updates" interface, select "Update All" to update the GD201 OS software

Done!

For more technical services on GODIAG GD201, please contact:

https://www.obd2shop.co.uk/

Oznake: godiag, godiag gd201

24.02.2022. u 04:09 • 0 Komentara • Print • # • ^

srijeda, 23.02.2022.

How to fix data getting error when using Lonsdor LKE key emulator

Customer question: Why do I keep getting the following error message when using the Lonsdor LKE smart key emulator?

The technician replied:

Reinstall the battery and follow the steps below:

Insert the LKE smart key emulator into the K518ISE device card slot,
Select "Special functions" in the device interface

Then, select "Simulate chip" == >> "Obtain LKE data" == >> "Obtain LKE key data"

Downloading application...

Generating...

Then, you will get the following information:

Click "OK" to continue, then click the return sign in the upper right corner of the device to return to the previous interface, select "Generate Simulated Chip" == >> "4D" == >> " 4D chip emulation

Displays the following information:

Click "OK" to continue

Generating...

The function test of the LKE smart key emulator was successful.

The operation of the video is as follows:
https://youtu.be/rbpLHoqOMpk
For additional technical support questions, please contact:
https://www.obd2shop.co.uk/

Oznake: lonsdor, lonsdor k518ise

23.02.2022. u 02:37 • 0 Komentara • Print • # • ^

Free Download SVCI J2534 Ford V1.2.5, IDS125, VCI V1.0.0.0(FAQs)

Here we provide 2022 latest version SVCI J2534 Ford V1.2.5, IDS125, VCI V1.0.0.0 free download link, all were tested by OBD2shop engineer. Rest assured download.

SVCI J2534 ford V1.2.5
https://mega.nz/file/fvpkxQAR#7Drt3vyEPSRGpbe4Tum5PzKvTH-5zbPJj6p4EFOLr2A

IDS 125
https://mega.nz/file/2ng0FajQ#n9Zf600-CvQtv48W2BToBaNqf9RK2KemJjHo63ZV4mI

SVCI J2534 VCI V1.0.0.0
https://mega.nz/#!anBG3CZa!SyersJzW3BA_FLFuBBK-hFU2JwGNvuPuWhxrT6QZWsk

SVCI J2534 FAQs
1. Does SVCI J2534 support Ford 650?
Yes

2. SVCI J2534 reprogram & calibrate 2003 F250 FICM module, possible?
Yes, it supports.

3. SVCI J2534 supports Ford Mustang Roush 2014?
Yes, it supports.

4. Can SVCI J2534 rewrite Ford Escape 1.6L ECU VIN & key programming?
Yes, it can.

5. Will SVCI J2534 damage the module in case not supporting the car?
For Ford & Mazda, it won’t.

6. Can SVCI J2534 do incode calculator for Ford 2010/ 2017 Ford Kuga?
Yes.

7. Can SVCI J2534 program 2012 Ford F-250 BCM?
Yes, it can.

8. Can SVCI J2534 work on 2015 Fusion ECM?
Yes.

9. Can SVCI J2534 program 2015 Ford Transit Custom all keys lost?
Yes

10. Can SVCI J2534 enable options in PCM speed control/ cruise control for 2008 Ford Crown Victoria?
Yes, it can.

11. Can SVCI J2534 reprogram PCM for 2009 Ford Edge?
Yes.

12. Use SVCI J2534 to do gearbox learning for 2013 Ford Fiesta, possible?
Yes.

13. Can SVCI J2534 support 2009 Ford Edge TCM upgrade to the latest?
Yes.

14. Can SVCI J2534 program Toyota Yaris 2009 PCM/ECU?
Yes, it can.

15. SVCI J2534 supports Ford trucks?
Yes. Specific model please contact online service.

16. SVCI J2534 can reprogram 2014 Ford Explorer smart key?
Yes, it can.

17. SVCI J2534 supports 2007 Ford F-250 6.0 diesel vehicle?
Yes.

18. SVCI J2534 supports Ford Transit 2015 PATS online programming?
Yes.

19. SVCI J2534 support OEM Mazda VCI?
Yes.

20. Latest SVCI J2534 support 2010 Ford Fusion PSCM?
Yes.

21. How to do if SVCI J2534 red light is flashing?
Press the button on device to reconnect.

22. Can SVCI J2534 read & write 2012 Ford F-350 ECU via OBD?
Yes, it can.

23. Can SVCI J2534 program 2012 Ford F-350 Super Duty ECU?
Yes.

24. Can SVCI J2534 program for 2015 Ford Fusion BCM, how to reset new VIN?
Yes. Use the IDS software.

25.SVCI J2534 supports 2017 Ford Flex to program smart key?
Yes.

26. Can FVDI J2534 program original ECU of the GEAR(TCU) online for Ford?
Yes.

27. SVCI J2534 reprogram 2018 Mazda 3 2.0G skyactiv Sportnav ABS module?
Yes.

28. Can SVCI J2534 relearn ECM & FOB separate keys for 2014 Ford Mustang 3.7L?
Yes, both can.

29. Can SVCI J2534 read & rewrite from cc3a 12a650 bda ECU on a 2012 Ford F-350 DRW 6.2L to an used ECU?
Yes, it can.

30. SVCI J2534 flash a 1999 Ford F250 V10 PCM, workable?
Yes.

31. Can SVCI J2534 support 2012 Ford Fusion made in US?
Yes.

32. SVCI J2534 supports 6.0 Ford Diesel power stroke 2003 Ford Excursion?
Yes.

33. Can SVCI J2534 do transmission programming?
Yes, it can.

More any questions feel free to contact us.
www.obd2shop.co.uk

Oznake: svci, svci j2534, svci j2534 ford

23.02.2022. u 02:03 • 0 Komentara • Print • # • ^

ponedjeljak, 21.02.2022.

XTOOL X100 PAD3 Program 2015-2020 Ford Lincoln AKL Instructions

This is an instruction on how to program 2015-2020 Ford Lincoln all keys lost alarm active situations with XTOOL X100 PAD3.

Tools You Need
XTOOL X100 PAD3(X100 PAD ELITE)
Main cable & OBD2-16 connector
Ford AKL Alarm Bypass Cable
Wi-Fi connection

How to Connect?
1. Connect the main cable (with OBD2 connector plugged) to the female OBD2 socket of the Ford cable, and connect the tablet(or VCI box, if it has one) to the other side of the main cable.
2. Connect the male OBD2 socket of the Ford cable to the OBD port of the vehicle.
3. Take the battery clip off from the car’s battery and connect the 2 battery clips(with the “Battery +/-” tag on it) to the battery.
4. There is also a battery clip(red cable with “Battery Clip +” tag on it) on the cable. Connect it to the positive battery clip on the car.

How It Works?
Ford AKL Alarm Bypass Cable can:
1. Allows you to perform Ford smart key all keys lost via XTOOL devices with a VCI box(H6Pros, A80Pros, X100MAXs, etc.)
2. Optimize the process on Ford smart key all keys lost via XTOOL devices without a VCI box(X100 PAD series, H6 Elites, D7/D8, etc.)
3. Controls vehicle battery on/off with a switch on your hand and saves your time from the repeating battery reconnecting process.

Operation Process
Here we take a 2018 Ford Edge with an active alarm as an example and read its EEPROM data without any keys available.

1. Make sure the cable is connected properly, then select the following menus on the tablet to get into this function.
Ford (V27.30 or higher) > North American Ford > Smart key system > Edge > 2016-2020
And this menu will show up.

2. Select “All keys lost”. Then choose the menu depending by the status of the vehicle. Considering the alarm is on now, here we select “Alarm activation”.

3. Now open the door on the driver’s side. Use a screwdriver to jam the door latch on the locked position(but keep it opening). The door should keep opened but locked until the entire process is done. When it’s done, click “OK” to continue.

4. Select “Reading EEPROM” first.

5. If the cable is connected, switch off the battery.

6. The device will try read the EEPROM by communicating with the ECU. When this notice shows up, switch on the battery and check it the alarm still goes on.

7. If the alarm is still on, switch off the battery and wait for 10s, then try switch off and on again.

8. If the alarm is off, disconnect the cable to the battery, connect it back to the battery clip of the car, tighten it, and close the hood. Click “OK” to continue.

9. Reading EEPROM data. This normally will take 10 minutes, please wait patiently.

10. When EEPROM reading is done, it will generate a bin file. Input the file name and save it on Internet Storage/ Adapter folder.

* if you’re using a device without VCI but not using the cable, you must remove/install the battery clip every time the device noted you to disconnect/ reconnect the battery.

More questions welcome to contact us.
www.obd2shop.co.uk

Oznake: xtool, xtool x100 pad3

21.02.2022. u 09:59 • 0 Komentara • Print • # • ^

petak, 18.02.2022.

KTM200 KTM1.20 Latest Software Free Download & FAQs

Different from KTM100, latest version KTM200 KTM1.20 ECU Programmer has added 379 new protocols, added 200 Bosch ECH read & write protocols without opening cover and updated 374 protocols. Users can return old dongle to upgrade KTM200 or PCMtuner V1.21, details please contact Obd2shop online service.

Free download KTM200 KTM1.20 Software
Link: https://share.weiyun.com/bG2lLOp5
Password: udv8ds
(If you don’t know how to download, feel free to contact us.)

KTM 200 67 in 1 ECU Programmer FAQs
Q: What’s KTM200 different from PCMtuner?
A: Both hardware are the latest version to support same functions at present. In addition to different appearances & factories, KTM software version is 1.20 while PCMtuner is 1.21. It’s said PCMtuner will update in the future.

Q: Both KTM200 & PCMtuner support network use?
A: Yes, both support.

Q: Can KTM200 support to program Marelli 9df by OBD?
A: Yes, apart from module 71/ 53/ 58, all other modules are programmed by OBD. This is exactly the OBD method.

Q: Does KTM200 support virtual reading?
A: Yes.

Q: What language does KTM200 support?
A: English & Russian.

Q: Can KTM200 read & write Volvo V50 2006 2.0 - sid803?
A: If the vehicle is SH7058 EEPROM(56) ECU chip, then it supports.

Q: Can I purchase KTM200 to upgrade old KTM Flash directly?
A: No. As for different hardware, please return back old dongle for an upgrade. Details please contact our online service.

www.obd2shop.co.uk

Oznake: ktm, ktm200, ktm tool

18.02.2022. u 09:44 • 0 Komentara • Print • # • ^

četvrtak, 17.02.2022.

Autel MK808TS vs. MP808TS vs. MS906 Pro-TS vs. Ultra

How to choose the best Autel diagnostic scanner among hot-sellers? Here Obd2shop has picked out 4 models for comparison, trying to help make a decision before the purchase.

MK808TS vs. MP808TS vs. MS906Pro-TS vs. Ultra Comparison

Difference
- Price
MK808TS < MP808TS < MS906 Pro-TS < Ultra

- Hardware
MK808TS = MP808TS < MS906 Pro-TS < Ultra

- Software Functions
MK808TS < MP808TS < MS906 Pro-TS < Ultra

- TPMS
All are featured with TPMS functions except Ultra

Conclusion
Autel MK808TS & MP808TS are same in hardware configuration. If you need a basic diagnostic tool, MK808TS is the best; If you need more like special functions, action test, Jaguar/ Vaxhall/ Opel offline programming, VW, Audi, Skoda hidden feature, then MP808TS is more recommended.

Maxisys Ultra is the most advanced diagnostic scanner that covering all features of others. Ultra has the widest compatibility, highest hardware to support the most advanced functions. That’s why it’s the most expensive Autel tool. It’s recommended for professional technicians or car repair shop who had budget.

Autel MS906Pro-TS is the latest launched MaxiSYS series scanner. It comes with latest hardware & software as Ultra. Especially the TPMS functions, which does not support on Ultra. If you prefer a latest Autel tool, MS906Pro-Ts is a fine choice.
www.obd2shop.co.uk

Oznake: Autel

17.02.2022. u 02:17 • 0 Komentara • Print • # • ^

srijeda, 16.02.2022.

Fixed: SVCI 2020 Registry Value RxFIFO or TxFIFO Have Wrong Data!

Problem
The SVCI 2020 is failed to communicate with a new BMW E46 2001 GEN that has been replaced recently. The warning “Registry value RxFIFO or TxFIFO have wrong data! May be there are problems! Under Windows NT/XP run OBDSetup.exe.” keeps coming out.

I’ve tried several times but was unable to clear the error. Any ideas?

Solution
Please follow the steps below, then re-connect the device to read fault codes again.
Step1. Open the SVCI 2020 installation directory.
Step2. Enter “C: Program File (x86)Abrites Commander Software ListCommon2” directory and copy BMW folder to “C: Program Files (x86)Abrites Commander Software ListCommon” directory

Hope this is helpful.
www.obd2shop.co.uk

Oznake: svci, svci 2020

16.02.2022. u 07:41 • 0 Komentara • Print • # • ^

utorak, 15.02.2022.

Scania VCI3 V2.50.2 Free Download & Installation Win10

Scania VCI-3 V2.50.2 is a wireless diagnostic software to do maintenance for all Scania trucks, buses, heavy vehicles or heavy duty engines. Here we provide the latest version to download that has been successfully tested.

Where to free download ScaniaVCI3V2.50.2
https://share.weiyun.com/mmCnKbt8
Password: 8xc3a5
Operating system: Windows10 64-bit
(If you don’t have an account, contact OBD2shop online service for help).
Note: this software requires to send us ID for activation after installation.

How to install ScaniaVCI3 Scanner?
https://www.youtube.com/watch?v=98CLoEU8oe8

1. Open “Adobe Reader 9.2” to install the program.

2. Unzip Scania package to start “SDP3_2.50.2” setup.

3. Run “prereqset64v3” file in FIX folder.

4. Restart the computer.

5. Locate & run “install” driver: FIX >> x64 folder.

6. Run “Hardware ID Reader” to get the ID, then send to us for activation.
7. Manage the added registry editor: Yes >> OK.

8. Copy all files in FILE TO REPLACE, paste to SDP3 folder for replacing.

9. Run Time >> Crack >> OK, restart the computer.

We can check if Scania VCI3 is installed successfully in Computer Management.

Done!
www.obd2shop.co.uk

Oznake: scania, scania vci3

15.02.2022. u 07:32 • 0 Komentara • Print • # • ^

ponedjeljak, 14.02.2022.

How to use Lonsdor ADP 8A/4A Adapter for 2017+ Toyota/ LEXUS?

Lonsdor Super ADP 8A/4A Adapter can work with K518 Programmer to do backup immo data, add smart key, delete smart key & generate key emulator(4A8A) for 2017+ Toyota/ LEXUS vehicles. Below is the operation guide for reference.

Lonsdor ADP Adapter Backup Immo Data
Backup immo data >> Finish connection as prompted >> Confirm software SN >> Enter file name to save, OK

Immo data backup successfully.

Lonsdor ADP Adapter Generate LKE Key Emulator
Prepare a LKE Smart Key Emulator in advance. Go to
Generate key emulator >> Make sure connection is OK >> Select file
Put the LKE Key Emulator into K518 card slot, click “OK”.
Emergency key generated successfully.
Please use emergency key to turn ignition on, then enter key programming function to program new key.

Lonsdor ADP Adapter Add Key(AKL)
For all keys lost, need to generate LKEKey Emulator as an emergency key firstly; Otherwise, no need.

Add smart key >> Make sure connection is OK
Switch ignition ON.
Confirm software SN.
Turn ignition off, turn on 2 flashing lights.
Load PEPS Dflash file to acquire 12-bit PIN.
OK >> Select Dflash >> Check current key count
Registered keys:2
Registrable keys:5

Finish the following steps within 30s:
1.hold the registered smart key’s back or generated emergency key closer to Start button, the buzzer beeps once, then take the key away from the button.
2.Hold the smart key(to be registered)’s back closer to Start button, the buzzer beeps twice, then take the key away from the button.

Just wait processing...
Operation completed!
Count of the registered keys:3
Count of registrable keys: 4

Switch ignition ON.
Place a programmed key close to start button of vehicle, then you hear one beep.
Programming complete.
Remember to check if the new key is workable.

Lonsdor ADP Adapter Delete Key
Prepare keys to be saved.
Delete smart key >> Make sure connection is OK
Note:
This function is used to delete all absent keys! Keys that do not touch ignition switch will be deleted, and can’t be registered to use.

Switch ignition ON.
Confirm software SN.
Turn ignition off, turn on 2 flashing lights.
Load PEPS Dflash file to acquire 12-bit PIN.
Select Dflash >> OK
1.Keep the keys to be saved close to the ignition switch, beep once.
2.The rest keys without closing to the ignition switch will be deleted.
Wait processing...
Deleting completed.
Count of the registered keys: 2

Buy Lonsdor K518ISE + Super ADP Adapter combination now to get lower price.
www.obd2shop.co.uk

Oznake: lonsdor, lonsdor k518ise

14.02.2022. u 02:39 • 0 Komentara • Print • # • ^

ponedjeljak, 07.02.2022.

Lonsdor K518ISE Program Range Rover Evoque 2018 AKL via OBD

Using Lonsdor K518ISE to successfully program a Range Rover Evoque 2018 via OBD when all keys lost. You’ll need to open the Lonsdor JLR License firstly. This vehicle is normally very difficult to program. But with K518ISE key programmer, it becomes an incredibly easy way in minutes. No EEPROM, no disassembly.

The JLR License is now available to program Lonsdor 2018-2021 JLR Key as well.
FAQs refer to:
http://blog.obd2shop.co.uk/lonsdor-jlr-2018-2021-smart-key-new-in-stockfaq/

In this case, you may need a Lonsdor 2015-2018 JLR Specific Key.

Connect K518 programmer with OBD, go into
Immo & Remote >> LAND ROVER >> Select from vehicle >> Land Rover(2015-2018) >> Smart key
*Here’s allowed to select 4 types:
Type 1(FK72)
Type 2(HPLA)
Type 3(write-to-start)
Type 4(program by OBD)

If programming FK72 or HPLA version via OBD, Lonsdor JLR Connector will be in need. Here we just select type 4.

Type 4(program by OBD) >> All smart key lost

Choosing all key lost will delete the original key from system.
New key only supports Lonsdor dedicated key.
Be sure before selecting.

JLR software update works for both FK75 and HPLA versions of KVM system.
Software version: FK72-14C104-AH

Do you have working key for this car?
Select “Cancel” for AKL.

Note: AKL operation will delete all the programmed keys, the unlocked working key can be re-programmed on the current vehicle. For the locked working key, please make sure it can be unlocked before programming. Otherwise, it will be deleted.

Select an key position with ID, press “Generate working key”.
Put the new key into K518 card slot.
Select key type: 1. Lonsdor dedicated key for Jaguar Land Rover.

Generated successfully.
If the vehicle is in alarm state, please press the remote’s UNLOCK button to disarm the alarm.

Test the key.
Key works great, we got a working key now.
Done!

I can’t think of a way that could have been any easier. K518 Programmer took me just a few minutes to reprogram this 2018 Range Rover. No need to do any kinds of EEPROM or take any computers out. No risk of breaking the system.
www.obd2shop.co.uk

Oznake: lonsdor k518ise

07.02.2022. u 05:43 • 0 Komentara • Print • # • ^

<< Prethodni mjesec | Sljedeći mjesec >>