obd2shop

ponedjeljak, 30.05.2022.

What's Godiag Full Protocol Obd2 Jumper? How to Use?

Godiag Full Protocol Obd2 Jumper is quite convenient to cooperate with ECU programmers & key tools via OBD in various scenes:
1. Work as EIS/ELV test line for Mercedes with CGDI or VVDI MB;
2. Work with key tools to program immo keys, like VVDI Key Tool Plus;
3. Work as tricore cable for ECU programmers to read data, such as MPPS, KESS V2, MPM, etc.
4. Provide power supply for ECU;
5. Convert vehicle power supply to 12V.

Features
1. Clear identification on each wire.
2. Equipped with a simulative ignition.
3. External 12V power supply connector.
4. Can connect to lock, ECU & BCM module.
5. Helpful for car repair & maintenance.

How to connect Godiag Obd2 Jumper?
1. Check ECU model: it's Cadillac E67.
2. Connect Godiag Obd2 Jumper according to ECU interface definition diagram, confirm all terminals are correctly connected.
3. Connect 120ohm CAN protocol resistor again.
4. Connect ECU dedicated regulated power supply & Godiag GT105.
5. Turn on the analog ignition switch to check whether the ECU can send CAN protocol communication.
6. Connect MPM ECU programmer to computer.
(Godiag obd2 cable supports to use alone, GT105 in the case is for checking protocols communication status. When GT105 indicators are flashing that means communication is normal.)

Application:
Clone Cadillac E67 with PCMtuner MPM + GT105 OK.

Read 2008 Chevrolet Avalanche E38 GM Gen4 ECM with MPM OK.

Program Benz W221 All Key Lost with VVDI MB Tool OK.

Read Audi A6 Simos 6.2/6.3 ECU data & password with VVDI2 OK.

Test ECU Status with Godiag GT101 PIRT Power Probe.

www.obd2shop.co.uk

Oznake: godiag

30.05.2022. u 15:57 • 0 Komentara • Print • # • ^

nedjelja, 29.05.2022.

How to Perform key adjustments via Autel Maxiim KM100

This post will go to perform key adjustments using the Autel Maxiim KM100 key tool, the key tool makes it easy to adjust the buttons on your key so that the transponder works the way you want it to.

Sometimes when you generate a new key, the transponder buttons are out of order, the lock button unlocks the door, the lock button opens the trunk, and so on. This Autel KM100 key tool can correct this aberration quickly.

In this post, the lock button is in the unlocked position and the unlock band is in the lock position.
How to adjust? Read on to find out.

Tap Special Function, place a blank key in the key slot, then tap Key Adjustment.

The system should automatically read the values, if it doesn't, tap read the current value.

If you want to change the location, tap the arrow on the right, here I want to change the location of the lock and unlock buttons.

The keys order works top to bottom, so we can see that the unlock button is in position 1, and the lock icon is in position 2.

Set the unlock button to position 2 by selecting the drop-down arrow.

Change the lock button's position to 1 by selecting 1.

Since that's all, I want to do I will tap confirm writing to complete the adjustment.

Tap read current value again.

Now the unlock button unlocks the door and the lock button locks the door.

For more details about Autel KM100 key tool, please check https://www.obd2shop.co.uk//autel-maxim-km100-key-programmer.html

29.05.2022. u 05:57 • 0 Komentara • Print • # • ^

četvrtak, 26.05.2022.

PCMtuner V1.26 ECU Programmer FAQs Collection

Here's collected the most frequently asked questions and answers for PCMtuner V1.26 ECU Programmer. Read this post to learn solutions when having same operation issues.

Q: Why my PCMtuner cannot connect to PC? Computer is not responding.
A: Attention please PCMtuner has 2 power supply: USB communication cable & PCB power supply cable. Many users tend to just plug the USB cable but not main cable, that's the reason why computer failed to connection.

Q: Why PCMtuner can identify ECU successfully, but failed to find device when click "Read"?
A: In this case, simply plug & unplug the power supply cable once.

Q: Why my PCMtuner account displays "unactivated"?
A: Account will be activated 24 hours after the application is submitted, please wait patiently.

Q: Why the device cannot find PCM Dongle or PCMtuner?
A: Please plug main power supply cable, USB cable & PCM dongle for connection.

Q: Where to log in my user account?
A: We'll generate 2 user accounts: VZ performance & Tunerbox.
VZ performance: Log in at https://support.vz-performance.com for VR files & damaos.
Tunerbox: Log in at https://www.tuner-box.com for technical assistance.

Q: Wiring connection is all correct, but PCMtuner cannot read?
A: Make sure you have selected the right mode(OBD/Bench/Boot). If connect without opening shell, please select No.71 protocol. Users should select correctly according to corresponding MCU (Can be found in wiring diagram).

Q: What cars support virtual files?
A: Toyota, VW, Audi, Honda can support virtual files.

Q: How to select virtual files?
Steps: Identify ID >> Search ID/ SW software no./ part no. >> Download corresponding files

Read also
Solution: PCMtuner device not found?" Error
http://blog.obd2shop.co.uk/solution-pcmtuner-device-not-found-error/

Solved: PCMflash "Unable to use selected interface" Issue
http://blog.obd2shop.co.uk/solved-pcmflash-unable-to-use-selected-interface-issue/

Solution: PCMtuner account Can't login "User already exist!!"
http://blog.obd2shop.co.uk/solution-pcmtuner-account-cant-login-user-already-exist/

Oznake: pcmtuner

26.05.2022. u 04:53 • 0 Komentara • Print • # • ^

utorak, 24.05.2022.

Free Download Thinkcar ThinkDiag App for Android Phone

Here obd2shop.co.uk provides 2022 latest free download Thinkcar ThinkDiag app for Android smart phone. Workable on Android 10 or 11 version system.

ThinkDiag APP Free Download Link:
http://apkdown.mythinkcar.cn/apk/index.php?mod=down&code=index&pid=12&id=668

Question
I've used ThinkDiag to test on BMW X5 2006, Vauxhall Astra 2010, Vauxhall Corsa 2008, VW Golf 2008/2015, Mercedes V250D 2017... But it always gave a note "Diagnostic service failure, please start it again". What's the problem?

Solution
ThinkDiag APP for Android 12 system is being developed now, please attention to normally work on a below system for the moment.

http://blog.obd2shop.co.uk/free-download-thinkcar-thinkdiag-app-for-android-phone/

Oznake: thinkcar, thinkdiag

24.05.2022. u 08:11 • 0 Komentara • Print • # • ^

petak, 20.05.2022.

How to use Autel MaxiIM KM100 to clone a key via 46 Password Calculation

This post will show you how to clone a key by calculating 46 passwords using the Autel MaxiIM KM100 key tool, now I will guide you step by step.

First, tap "Reading/Cloning" on the key tool, then tap clone, next tap "46 password calculation" at the top.

On this page, place your key in the key slot at the top
Press "start" to recognize the key

Next, we need to take it apart so that the key battery doesn't interfere with the password calculation process.

Place the key component and the transponder head close to the start button, then turn the engine on.

You may need to press the start button two or three times for it to successfully read the password.

Once you reach this stage it may take up to 3 minutes for the password to be calculated.

Take a picture of the password once it appears as you will need it if you are performing a simulation.

If you have any questions about Autel MaxiIM KM100, please feel free to contact us.

http://blog.obd2shop.co.uk/how-to-use-autel-maxiim-km100-to-clone-a-key-via-46-password-calculation/

Oznake: autel maxiim km100

20.05.2022. u 05:02 • 0 Komentara • Print • # • ^

srijeda, 18.05.2022.

Yanhua Mini ACDP + Module 24 Add JLR 2018+ Smart Key

This is a tutorial on how to add Jaguar/ Land Rover 2018+ smart key with Yanhua Mini ACDP & Module 24. The procedure requires a working key, read the post below to learn how it works.

Step1. Replace RFA Module/ RFA Chip
You can replace a new RFA module according to vehicle RFA model. Also you can replace the RFA main chip.

Step2. Write Initial Data
* If your chips or modules already have original data, you can skip this step. Otherwise, the initial data needs to be written.

Note: Please confirm the current module is a new RFA module or the the RFA main chip has been replaced with a new chip!

Tools Required:
Module 24
RFA module
20PIN cable
OBP+ICP adapter
ACDP programmer
Connect ACDP host, OBP+ICP adapter, interface clip & RFA module.

Mini ACDP >> Jaguar/ LandRover >> Program smart key(2018-) >> RFA write initial data >> SPC560B60L3 >> Write initial data >> JPLA(select the option according to RFA module)
To check connection diagram, press "Help".

Please connect ACDP with RFA module, don't cut the power or pull out the device during the programming!

Pin detection passed. If fails, please adjust the clip position to re-test.
Prepare to download data from the server, please keep the network stable during the download!
Prepare to write data, please do not power off or unplug the device & adapter during data writing!
Writing CFLASH data, please wait...
Writing chip data finished.
Save data file success.

Step3. Identify RFA Information
Remove the clip and install the interface board.
Identify RFA Info >> Continue
Check the system information, make sure the RFA module is unlocked.
Read system info finished.
Save info file success.

Step4. Program Key via OBD
Load the RFA module, connect ACDP programmer to the vehicle via OBD.
Prepare 2 smart keys that can be programmed(working key is acceptable).

Replace RFA(JPLA/K8D2) program key >> Add smart key(auto mode)
Connect ACDP to the vehicle OBDII port.
Confirm the system information,
Continue >> OK

Prepare to program, please make sure the stable power supply and DO NOT pull out the device during the programming!
Confirm the current vehicle ignition is off, the program will automatically open the ignition!

Programming RFA module is complete, the smart key program process is about to begin. Press "Continue".
Confirm the current vehicle ignition is off, the program will automatically open the ignition!

Please prepare at least 2 new keys and put them in the car. Press the unlock key during key learning process. Press "OK", follow the prompts to start program keys. Please complete all the key learning operation within 30s.

Please hold the smart key that need to program in your hand.
Press the unlock button hard for 4s, and the car horn will sound twice to indicate that the current key has been programmed successfully.

The first smart key has been programmed.
Please prepare the second smart key to be programmed!
Just repeat same operations as before...

Key programming successful.
To add more keys, press "Yes". Otherwise, press "No".
Please confirm the key information, press "OK".
Done.

http://blog.obd2shop.co.uk/yanhua-mini-acdp-module-24-add-jlr-2018-smart-key/

Oznake: yanhua mini acdp

18.05.2022. u 09:10 • 0 Komentara • Print • # • ^

ponedjeljak, 16.05.2022.

Yanhua ACDP Module 25: VW/Audi 0DE Gearbox Mileage Correction

Latest Yanhua Mini ACDP Module 25 was released, supported to adjust VW/ Audi DQ380(0DE), DQ381(0DE), DQ500(0DE) gearbox mileage. Much safer without soldering. Should work together with Mini ACDP Programming Master.

Supported Car Model:
Audi: A3, Q2, Q3, etc.
Volkswagen: Magotan, Passat(B8), Lamando, Golf GTI, Tiguan L, Teramont, new Skoda, etc.

Functions:
1. Identify gearbox model by OBD quickly.
2. No need to remove TCM, plug and play to correct mileage with special interface board.

Path in Mini ACDP APP:
VW >> Gearbox mileage correction >> VW/Audi >> DQ380(0DE)/DQ381(0DE)/DQ500(0DE)

Here's allowed to do identify, mileage correction(auto mode/ single step mode), time correction(auto mode/ single step mode), read & write EEPROM.

How to connect ACDP Module 25?
Tools required:
SH725xx-0DE interface board
DB15-LAN adapter
TCU cable
Mini ACDP Basic module
VW/ Audi gearbox

Step1. Connect SH725XX-0DE to gearbox correctly as image.

Step2. Short the CAN resistor on the DB15-LAN adapter to CAN-R.

Step3. Connect ACDP, DB15-LAN adapter, interface board & gearbox.

www.obd2shop.co.uk

Oznake: yanhua mini acdp

16.05.2022. u 15:01 • 0 Komentara • Print • # • ^

četvrtak, 12.05.2022.

Hot 4 Injector Cleaner & Tester Machine 2022, How to Choose?

Here Obd2shop.co.uk have collected the latest hot injector cleaners & tester machines in 2022. Covering 4-cylinder & 6-cylinder machines from Summary, Autool, Launch, Tektino. By making a list of the differences to help consumers make a better choice.

Hot 4 4-Cylinder Injector Cleaners
Summary vs. Autool vs. Launch Comparison

Hot 4 6-Cylinder Injector Cleaners
Summary vs. Autool vs. Launch vs. Tektino Comparison

Conclusion
From the comparison table, Summary supports the most features while other brands are not or less.

However, remember to make sure the injector cleaner you're purchasing is work for your car. As choosing an appropriate machine can greatly save money than going to maintenance.

Article source: http://blog.obd2shop.co.uk/hot-4-injector-cleaner-tester-machine-2022-how-to-choose/

Oznake: injector cleaner

12.05.2022. u 15:12 • 0 Komentara • Print • # • ^

utorak, 10.05.2022.

Solution: "PCMtuner device not found!" Error

Please notice not upgrade PCMflash 1.20 to above version in V1.25 PCMtuner software. Or else, this may cause "PCM Tuner Device not found!" error, failed to identify PCMtuner Dongle or to do any read and write jobs.

Solution
1. For upgrade misoperation, uninstall then re-install PCMflash 1.20;
Free download PCMflash 1.20 software:
https://mega.nz/file/xwMWiSYb#CVsKxEyCTjRTEnpe9me

mWCzywKihxEf0mO5OmgX4X0g

2. If the error still exits for other cases, unplug & re-plug PCMtuner Dongle, then restart PCMtuner ECU programmer.

Problem will be solved.

Hope this is helpful.
www.obd2shop.co.uk

Oznake: pcmtuner

10.05.2022. u 08:30 • 0 Komentara • Print • # • ^

ponedjeljak, 09.05.2022.

Solved: VXDIAG VCX SE VW ODIS "trial period has expired!"

Problem: The VW ODIS 9.10 Software for VXDIAG VCX SE is unable to open. It prompts:" Sorry, but your trial period has expired! You have exceeded 50 trial executions! Please, register this software to remove trial limitation!"

Solution
Install the unlimited patch below can solve the problem.

Free download VW ODIS 9.10 unrestricted patch:
https://mega.nz/file/0llgTITI#BfxJchSKpMAeOXX_1OtN2HO0h6tCUbpFRNbWkOH7U4w
Size:3.6MB

The patch is used to repair VW expired trial issue in 2TB Software HDD.
Any questions please contact us.

Technical support
www.obd2shop.co.uk

Oznake: vxdiag vcx se

09.05.2022. u 14:58 • 0 Komentara • Print • # • ^

nedjelja, 08.05.2022.

This is a simple solution way to solve "Launch X-431 Pad VII does not respond" prompt after powered on. Generally at this time, users should reinstall the latest program version to try or restore the factory settings to install. That sounds troublesome, follow the steps below can repair it easy.

How to restore X431 main program to factory version?
This is taking X-431 Pad V as an example, applies to most Launch- x431 scanners.
Step1. Uninstall
Other Modules >> Tablet Setting >> Apps >> X-431 PAD V >> Tap top right corner >> Uninstall updates
Replace this app with the factory version? All data will be removed. OK
Uninstall finished.

Step2. Reinstall
Log in >> Software Update >> Select "AutoSearch" & "APP application program" to update.

Problem was solved.
Completed.

www.obd2shop.co.uk

Oznake: Launch X431

08.05.2022. u 15:35 • 0 Komentara • Print • # • ^

subota, 07.05.2022.

Creator C110+ BMW Code Reader Update

This post will show you how to update your Creator C110+ BMW Code Reader.

Part 1. Creator C110+ BMW Update Tool Download and Install

1. Open your browser, enter the URL “szcreator.com”, find “Download” on the website home page ’ select “C1XX, C3XX, C4XX, Update Tools”, find “UpdateTool_V3.rar” and download it.

2. Still on the current page, click on "C110 +", find "C110_V7_0_EN.RAR" and download it.

3. Unzip the following two files and install them on your desktop.

4. Open and run "UpdateTool_V3", and follow the instructions, at the end of the installation, the icon will appear as shown in the figure.

Part 2. Creator C110+ BMW Code Reader Update

Connect Creator C110 + to computer via USB cable, open "Creator C110" icon, select "Update", then select "C110_V7_0_EN.RAR" to do the update.

src="https://blog.dnevnik.hr/obd2shop/slike/m/creator-c110-bmw-code-reader-update-6.jpg" alt="" />

The update is complete!

For more detailed steps, refer to this video:
https://youtu.be/Qs-BwK0l2Gs

Oznake: creator c110+ bmw code reader

07.05.2022. u 15:51 • 0 Komentara • Print • # • ^

petak, 06.05.2022.

Lonsdor K518ISE + ADP Adapter Program 2021 Toyota RAV4 AKL

Lonsdor K518ISE + ADP 8A/4A Adapter can program 2021 Toyota RAV 4 all keys lost successfully. No need to disassemble, should use LKE smart key to make an emergency key firstly.

Follow is the procedure:
Connect to EPES module.
Insert ADP 8A/4A Adapter into K518ISE programmer.

Backup Immo Data
Immo & remote >> TOYOTA >> Select from type >> all smart key lost(2016-) >> 8A >> Backup immo data >> Read notes, OK >> OK >> Enter file name to save >> OK
Immo data backed up successfully.
Remember to record file path.
Press "OK" to continue.

Generate Emergency Key
This function can load backup data to generate an emergency key in AKL situation, then use this key to turn on dashboard to add keys.
Press "OK".

This function requires Internet connection.
Please put key emulator into K518 Programmer card slot and press "OK".
Select backup file, press "OK".
Read operation hints:
1. Press ignition switch once.
2. Quickly place LKE vertically on ignition switch, keep the antenna end of LKE aimed at the central position of ignition switch, and wait until dashboard lights up.
3. If dashboard fails to light up after 3s, please try to repeat step 1&2.
4. If dashboard fails to light up after multiple attempts, please contact after-sales for technical support.
Press "OK".

Reconnect the original car cable and touch the key to START button.
The car successfully worked.

Add New Key
Key info:
TOYOTA RAV4 2019-2021 genuine smart remote key,
315Mhz,
8990H-0R030.

Press "Add smart key".
Please switch ignition ON.
This function can use a registered working key or emergency key to add new keys.
Turn ignition off, turn on 2 flashing lights.
Select "Load D-FLASH data of PEPS to acquire 12-bit PIN".
OK >> Load backup dat
Wait for processing...
Count of the registered keys: 2
Count of registrable keys: 5
Press "OK".

Step1. Hold the registered smart key or generated emergency key closer to Start button, the buzzer beeps once, take the key away from the button.
Step2. Hold the smart key(to be registered) closer to Start button, the buzzer beeps twice, then take the key away from the button. To program more keys, please repeat step2.
Finish above steps within 30s.

Count of registered keys: 3
Count of registrable keys: 4
Please follow the prompts to finish operation, press "OK".
Switch ignition ON.

The car & remote worked successfully.