OBD2 tools on OBD2shop.co.uk https://blog.dnevnik.hr/obd2shop
srijeda, 30.11.2022.
Launch X-431 Pad 7 Program 2018 BMW 530LI xDrive G38 EPS
How to use Launch X-431 PAD VII to program BMW ECU? This is programming the 2018 BMW 530LI xDrive G38 EPS as instructed.
Local diagnose >> BMW >> OK >> Automatically Search >> 5 Series >> 5'_G38 >> Coding/Program >> Program >> Read tips, OK >> Automatic Programming
Confirming the transport mode...
(Some MILs have been lighted which is a normal phenomenon)
Operation Tips
Local programming backup information detected:
1. Quickly press the last configuration to access.
2. If the hardware changes, press "No" to calculate the new configuration information.
3. If the vehicle command changes, press "No" to calculate the new configuration information.
4. If the programming indicated the hardware is mismatched, press "No" to calculate the new configuration information.
5. For any uncertainty, press "No" to calculate the new configuration information.
Whether to quickly load the last configuration information? Press "No".
Succeeded to get the other vehicle information...
Next >> EPS(Electronic Power Steering) >> OK >> Program >> Select files(asterisk means it must be selected) >> Next
Please confirm the vehicle conditions:
1. The vehicle is connected to an external power supply or the vehicle power supply can support the steady discharge for at least 1 hour.
2. The vehicle voltage can be stable for at least 13V.
3. Ignition on(engine not start).
4. Switch off all electricity-consuming equipment, eg. air conditioner.
Press "Yes".
Downloading files...
Continue or not? Yes
X-431 PAD 7 will start programming automatically...
ECU restart...
Testing...
Clear fault code...
Programming completed.
*DO NOT disconnect immediately, as it needs to complete the coding.
Recoding has been completed.
Done.
www.obd2shop.co.uk
Oznake: launch x431 pad 7
ponedjeljak, 28.11.2022.
Launch X431 X-Prog3 IMMO Wire Connection Instruction
Launch X-Prog 3 Immobilizer Programmer is used to read & write car key chip data, compatible with a variety of X431 diagnostic tools like X431 V+, X431 PRO5, X431 PRO3S+, etc.
This is a quick guide on how to connect GIII X-Prog3 with the X431 scan tool.
Connection Instruction
1. Plug in the DBSCAR connector line.
2. Connect DBSCAR to the X431 scanner via a USB cable.
3. Connect DBSCAR to X-Prog3 via a three-way extension cable.
4. Insert MCU-V3 board into X-Prog3 if any.
5. Connect the power cable to the MCU board via a three-way cable. Plug the BENCH cable into the MCU board.
6. Connect the BENCH cable & control unit via flash cable.
Completed.
www.obd2shop.co.uk
Oznake: Launch X431
petak, 25.11.2022.
How to use foxFlash Manager Tool
When you receive your foxFlash, how do you use it? This article will guide you on how to do it, let's take a look!
1. Go to https://www.dfb-technology.com/download.html and download the foxFlash Manager app, then install it.
2. Register this app with your email.
3. Enter your binding code on your device.
NOTE: Don't spread your SN on the internet, or others will try to steal your tool's password.
4. Connect your foxflash tool to your laptop via a USB cable, then click the download button located in the foxFlash app inside.
5. After the download is complete, open the folder C:Program Files(x86)FoxFlash ManagerfoxflashDFB TechnologyDFBTech_DRIVER, then install the drivers.
6. Unplug your foxFlash tool, then plug the USB back in.
7. Click the "Activated" button of the foxFlash manager app until activated, then run the foxFlash app on the desktop, then enter the password in the windows, and click login.
Note: Always run foxflash manager app whenever you need to use our tool. Run it then click the active button, it will continue to allow the tool to access our server.
For more technical services of foxFlash, please follow https://www.obd2shop.co.uk//fox-flash-ecu-tcu-clone-chiptuning.html
Oznake: foxflash ecu programmer
četvrtak, 24.11.2022.
Obdstar X300 DP Plus Program 2019 Lexus RX300 Key by OBD
Obdstar X300 DP Plus is supported to program 2018+ 8A-A9 Camry, Lexus, IZOA, CHR, LS add keys & all keys lost with free Pincode by OBD. Need to work with Key SIM, follow the steps below to learn.
Tools Required
Main Cable
Key Master DP Plus(X300 DP Plus)
Key SIM
Procedure
Full operation video:
https://www.youtube.com/watch?v=ZGZkTfd_kiQ
1.Read & Save IMMO Data
Connect X300 DP Plus with the vehicle by OBD.
Car IMMO >> Asia >> Lexus Toyota Scion >> Latest version >> Manual select model >> LEXUS >> ASIA >> RX series >> Proximity >> 2018-(8A-A9) >> Read immo data >> With gateway 8A-A9 >> OBD
This function is available by connecting the server, please ensure the Internet connection is normal.
Save data file.
2.Make Simulated Key
Go back to "Make simulated card".
This function is available by connecting the server, please ensure the Internet connection is normal.
This function can generate an simulated card with all keys lost.
Use this simulated card instead of the original car key to approach the start button and turn on the instrument, perform "add smart key" operation.
Make sure the simulated card is fully charged, otherwise the add smart key operation may fail.
Select immo data >> Enter >> Key sim simulator
Please connect key sim simulator.
Generating the A9-type simulated card, please wait for 1-2 minutes...
Generate simulated card successfully.
Move the simulated card close to the start button and try to light the meter. If you can light up the meter normally, use the simulated card instead of the original car key for the "Add smart key" operation.
Now you're allowed to go on adding keys. The operation is also applied to all keys lost situation.
Read also
OBSDSTAR Upgrade: Toyota/Lexus 2018+ 8A-AA Add Keys & AKL
www.obd2shop.co.uk
Oznake: obdstar x300 dp plus
utorak, 22.11.2022.
OBD2shop.co.uk Black Friday Sale is On...
Is your wishlist ready? The OBD2shop.co.uk Black Friday Sale is now live! Special offer for multiple products!
Shop now>> https://www.obd2shop.co.uk/
The following hot-selling products with the best price, you cannot miss them!
Xhorse
Xhorse VVDI PROG
Latest price: £399 Buy now: £379
VVDI Key Tool Plus
Latest price: £1,979 Buy now: £1,666
Dolphin XP005 Key Cutting Machine
Latest price: £1,539 Buy now: £1,479
VVDI Mini Key Tool
Latest price: £110 Buy now: £106
Xhorse Key Reader
Latest price: £323 Buy now: £295
VVDI Super Chip (10pcs/lot)
Latest price: £28 Buy now: £26
and more...
Launch X431
Launch X431 V
Latest price: £689 Buy Now: £625
Launch X431 V+
Latest price: £889 Buy Now: £772
Launch X431 V+ Plus HD3 Module
Latest price: £1,589 Buy Now: £1,444
Launch CRP909E
Latest price: £369 Buy Now: £344
Launch X-431 Pad VII
Latest price: £3,019 Buy Now: £2,403
Launch X431 PRO5
Latest price: £1,359 Buy Now: £1,203
and more...
Autel
Autel MaxiIM IM608 Pro with XP400 Pro
Latest price: £1,999 Buy Now: £1,899
Autel MaxiIM IM508
Latest price: £789 Buy Now: £755
AUTEL MaxiDAS DS808 KIT
Latest price: £685 Buy Now: £629
Autel MaxiTPMS ITS600E
Latest price: £425 Buy Now: £406
AUTEL MaxiSYS MS906
Latest price: £775 Buy Now: £721
and more...
Lonsdor
Lonsdor K518ISE Key Programmer
Latest price: £1,100 Buy Now: £999
Lonsdor JLR Smart Key
Latest price: £56 Buy Now: £52
CGDI
CGDI Prog MB
Latest price: £579 Buy Now: £542
CGDI Prog BMW
Latest price: £579 Buy Now: £542
CGDI Prog MB with ELV Repair Adapter
Latest price: £588 Buy Now: £573
CGDI MB with Full Adapters for ELV Repair
Latest price: £607 Buy Now: £555
Yanhua ACDP
Yanhua Mini ACDP with 12 Modules
Latest price: £2,129 Buy Now: £2,036
Yanhua Mini ACDP Plus JLR KVM Module
Latest price: £490 Buy Now: £462
MB SD C4
MB SD C4 Plus Without Software
Latest price: £431 Buy Now: £406
MB SD C4 Plus + 500G HDD software
Latest price: £462 Buy Now: £444
Super MB PRO M6
Super MB PRO M6 with Latest SSD Plus Lenovo X220 4GB Laptop
Latest price: £629 Buy Now: £619
Super MB PRO M6 Full Configuration
Latest price: £481 Buy Now: £444
Super MB Pro M6 Without Software
Latest price: £431 Buy Now: £412
ECU Programmers
PCMtuner ECU Programmer
Latest price: £413 Buy Now: £351
Fetrotech Tool Black Color
Latest price: £312 Buy Now: £258
PCMtuner Plus KESS V2 Plus KTAG (Bundle kit)
Latest price: £542 Buy Now: £490
Full Version KT200 ECU Programmer
Latest price: £703 Buy Now: £657
and more...
Oznake: Black Friday
ponedjeljak, 21.11.2022.
Yanhua Mini ACDP + Module 27 Read BMW MSV90 DME ISN
Yanhua Mini ACDP + Module 27 supports reading, writing, and cloning BMW E/F chassis ISN without having to open the DME shell. Apply to MSV80, MSD80, MSD81, MSD85, MSD87 MSV90 Continental/ SIEMENS DME types.
This is reading BMW MSV90 DME ISN on the bench as an example, follow the post carefully to learn how to do it. To check the connection diagram, please click "Help".
Check the full video to learn:
https://www.youtube.com/watch?v=aw1e7cG3nvk
Accessories
BMW MSV90 DME Module
MSV90 interface board
20PIN cable
ACDP host
OBD+ICP adapter
Install the MSV90 interface board.
Short the CAN resistor on the OBP+ICP adapter to the CAN-R-Join side.
Connect the MSV90 DME & ACDP host.
Operation
Mini ACDP >> BMW >> DME ISN >> BENCH Mode read/write DME ISN >> SIEMENS/Continental DME >> Fxx >> N52(MSV90) >> Read ISN >> Continue
Confirm the system info and save the screenshot.
Please take a screenshot and export the ISN data.
Export >> Save >> OK
ISN data is exported successfully.
Reading ISN data finished.
www.obd2shop.co.uk
Oznake: yanua mini acdp
srijeda, 16.11.2022.
Yanhua Mini ACDP Program JLR(2015-) KVM Add Key/All Keys Lost
This is a tutorial on using Yanhua Mini ACDP + Module 9 to program Land Rover 2010-2019 KVM add key & all keys lost. Users can click "Help" in app to check the connection info.
Normally, Land Rover's KVM module is at the left side or right side of the vehicle trunk. Jaguar's KVM is at the right side of the rear seat or in the front of passenger seat.
Preparation
Blank key
BAV-KEY adapter
KVM interface board
ACDP host
Copper pillar
OBP+ICP adapter
20PIN cable
KVM module
1.Install the copper pillar, align D1-D4 test points. As long as the 4 test points are aligned, then all test points are aligned.
2.Lock the board with PCB lock & copper pillar. Connect the OBP+ICP adapter & KVM interface board.
3.Connect the adapter & ACDP host, power up ACDP.
Operation
Mini ACDP >> Jaguar/ Land Rover >> ICP Add key/All key lost(2015-) >> KVM ICP(MC9S12XEQ384) >> Add key auto mode
Note:
1.Please prepare the OBP+ICP adapter, KVM interface board, KVM module, BAV adapter and blank key.
2.Save the original EEPROM, DFLASH data& the ones after programming the keys according to the software prompt.
3.ACDP device is forbidden to be powered off during the process of adding a key, otherwise it will cause the key to fail to be added.
Precautions:
1.Ensure the well connected for ACDP device, OBP+ICP adapter, KVM interface board & KVM module.
2.Follow the software prompts to save the chip data read from KVM module.
Pin detection passed. If the detection fails, please check and clean the test points.
Press "Continue".
It is detected that the KVM module chip has been encrypted. Press "Continue".
Please save the original PFLASH data of the KVM module.
Please save the original EEPROM data of the KVM module.
Please save the original DFLASH data of the KVM module.
Check the VIN number and other vehicle info, press "Continue".
Note:
1.To maintain the ACDP device power-on state, first disconnect the OBP+ICP adapter from the ACDP device(keep the OBP+ICP adapter, KVM interface board and KVM module connected).
2.Then connect the ACDP device to the BAV-KEY adapter and place the programming key correctly on the BAV-KEY adapter.
Current key ID: 822D4E37
Choose the unoccupied key ID displayed as 000: Key3
Please save the EEPROM data of the KVM module after adding the key.
Please save the DFLASH data of the KVM module after adding the key.
Note:
1.Keep the ACDP device powered on. First disconnect the BAV-KEY adapter from the ACDP device.
2.Then connect the ACDP device, OBP+ICP adapter, KVM interface board and KVM module to ensure normal communication.
Continue >> Continue
Check the IMMO info. As you can see, the new key ID is in the key list.
Writing chip...
Adding the key completed.
Please install KVM module to the car and confirm that the new key can be used normally!
OK >> OK
This is how to use Mini ACDP JLR KVM Module for key programming.
www.obd2shop.co.uk
Oznake: yanhua mini acdp
ponedjeljak, 14.11.2022.
Launch X-431 Pad7 Register New Nissan X-Trail ECM VIN
This is a guide to using Launch X-431 Pad VII to perform new ECM(Engine Control Module) VIN registration for a 2017 Nissan X-Trail T32. It's very helpful for ECM replacement in vehicle repair.
Procedure
Nissan Latest version >> Full system diagnosis >> The vehicle with 16PIN >> System selection >> Engine >> ECM(Engine Control Module)
X-431 Pad7 is scanning ECU... please wait
Special function >> VIN registration
Confirm the ignition switch is on and the engine stopped.
Hold these conditions during this procedure.
Touch start.
As we can see, the VIN/Chassis value is blank now.
VIN Read >> Input
Input the VIN of the vehicle. Refer to S/M for the location of the identification plate.
Write >> Input
Input VIN once again.
Press "Start".
Command succeeded.
Turn the ignition switch off for 10s, then the ignition switch on to confirm no DTC.
Exit to enter into "VIN registration" again.
The VIN/Chassis value was displayed, which means the VIN number has already been registered successfully.
Done.
www.obd2shop.co.uk
Oznake: launch x431 pad 7
srijeda, 09.11.2022.
KT200 V11.01 Software Free Download & Installation Guide
KT200 ECU Programmer latest software version V11.01 has released, here you can free download & guide to install.
Where to free download KT200 v11.01?
Mega: https://mega.nz/file/NPM0GDZb#PVVHI2mXLekSAiRNd1UvHEom4wLtKcc64isJB7SV6m8
Weiyun: https://share.weiyun.com/T1ZVPy6u (password: zug4hj)
Size: 38.7MB
Compatible system: Win7, Win8/8.1 Win10, Win11.
How to install KT200 v11.01?
Operating video:
https://youtu.be/0Ohi32mexaM
Step1. Click "KT200setup-11.01" package to install software.
Step2. Install & update KT200 driver:
Computer management >> Device manager >> DESKTOP-FSN5GTS >> Other devices >> DFBTech >> Update driver >> Browse my computer for drivers >> Selected "DFBTech_DRIVER" folder >> Next
Step3. Download software & diagram
Start "KT200 Service" >> Download Software
Start downloading software, old version will be completely uninstalled and deleted!
Click "Yes".
Download finished, install or not? If you choose YES, current version will be uninstalled before installation.
Click "Yes".
Yes, I accept the terms of the License Agreement! >> Next >> Next >> Finish
Reset device successfully!
Restart "KT200 Service" >> Download Diagram
Start downloading documents!
Yes >> Finish
Completed.
Now you can start to use Full Version KT200 software.
www.obd2shop.co.uk
Oznake: kt200 ecu progarmmer
ponedjeljak, 07.11.2022.
Autel IM508 Generate GM Buick ID46 Key as KM100
Autel MaxiIM IM508 Key Programmer can support the key generation function now. No having to buy extra Autel KM100, as long as updating to the latest version. It's also available to work with XP200. Following I'm gonna generate a GM Buick key as a demonstration.
Connect Autel IM508 to XP200, go to
Universal key >> Accept >> Universal key generation >> Asia >> GM >> Buick >> All remotes >> 433M old style
Put Autel Universal Key into XP200 programmer keyhole.
Press "Generate universal key".
Wait to generate until 100%...
XP200 light will keep fast blinking during the period.
Universal key generation is completed.
Now we can go on programming the key with Autel IM508.
In the whole process, all you need is only one device from start to finish. However, if you still haven't any key tools right now, KM100 will be a good choice as well.
www.obd2shop.co.uk
Oznake: autel im508, autel km100
petak, 04.11.2022.
(Fixed) Yanhua Digimaster 3 prompts (1E10) Program device error
Customer Problem: When I use Yanhua Digimaster 3 to adjust the mileage of my 2006 sport range rover, a (1E10) Program device error is displayed, please tell me what to do.
Solution: Digimaster 3 can read mileage normally, but can't adjust because the chip is not soldered well, you can solder it again.
For more technical services of Yanhua Digimaster 3 mileage correction tool, please follow http://blog.obd2shop.co.uk/
Oznake: yanhua digimaster 3
četvrtak, 03.11.2022.
OBDSTAR X300 DP Plus Reads Pincode for 2021 Hyundai Tucson Proximity by OBD
This post will guide you on how to use OBDSTAR X300 DP Plus to read the 2021 Hyundai Tucson Proximity Pincode by OBD.
Plug the OBD connector into the car.
Open X300 DP Plus, select "DP" >> "CAR IMMO"
Then choose "Asia">>"HYUNDAI/KIA/GENESIS">> "HYUNDAI/KIA/GENESIS V31.41", and press "Enter" to continue.
Then choose "Read PinCode">>"PROXIMITY">> "8A Proximity-Hitag 3".
This function is available by connecting the server, please ensure the internet connection is normal.
Communicating...
The PIN Code read successfully!
Video reference:
https://youtu.be/On5mg_oyTCI
For more technical services of OBDSTAR X300 DP Plus, please follow http://blog.obd2shop.co.uk/
Oznake: obdstar x300 dp plus
srijeda, 02.11.2022.
Xhorse Dolphin XP-005 Cut VW Audi HU162T Key Tutorial
Xhorse Dolphin XP-005 Key Cutting Machine supports cutting the latest HU162T key with 9/10 bittings, such as VW Golf 7 or Audi. This is a tutorial on how to cut this particular type of key.
1. Go to Cut By Bitting >> HU162T-10/ HU162T-9
Eg. Taking cut 9 bittings as an example.
2. Decode the front 9 bittings & select B clamp first, then continue to cut this side.
3. Return to the previous page, and select 3 bittings & D clamp. This will need another HU162T key blank to fix the key firmly. Go on to decode key, then cut key.
That's it!
The cutting steps apply to Dolphin II as well.
Oznake: xhorse dolphin xp005l
utorak, 01.11.2022.
(Solved) KT200 Software V2022.10.01 cannot work
Problem: Recently, some customers reported that when the latest version of KT200 software V2022.10.01 is installed, the gray menu is displayed and cannot be selected and the voltage is not displayed either.
Solution: Uninstall the version 2022.10.01 software, then re-download and install the version 2022.08.20 software.
KT200 V2022.08.20 Download:
https://mega.nz/file/d6YFDD4Z#sIdJrT_V1N7KOQtCBob2feLLj4cH3gZ2yRcMdpEBMrA
Oznake: kt200 ecu progarmmer
| < | studeni, 2022 | > | ||||
| P | U | S | Č | P | S | N |
| 1 | 2 | 3 | 4 | 5 | 6 | |
| 7 | 8 | 9 | 10 | 11 | 12 | 13 |
| 14 | 15 | 16 | 17 | 18 | 19 | 20 |
| 21 | 22 | 23 | 24 | 25 | 26 | 27 |
| 28 | 29 | 30 | ||||
Rujan 2024 (7)
Kolovoz 2024 (14)
Srpanj 2024 (12)
Lipanj 2024 (10)
Svibanj 2024 (13)
Travanj 2024 (12)
Oujak 2024 (11)
Veljača 2024 (2)
Siječanj 2024 (10)
Prosinac 2023 (8)
Studeni 2023 (6)
Listopad 2023 (7)
Rujan 2023 (9)
Kolovoz 2023 (6)
Srpanj 2023 (10)
Lipanj 2023 (4)
Veljača 2023 (8)
Siječanj 2023 (14)
Prosinac 2022 (13)
Studeni 2022 (14)
Listopad 2022 (18)
Rujan 2022 (9)
Kolovoz 2022 (16)
Srpanj 2022 (11)
Lipanj 2022 (14)
Svibanj 2022 (13)
Travanj 2022 (12)
Oujak 2022 (12)
Veljača 2022 (13)
Siječanj 2022 (10)
Srpanj 2021 (1)
Studeni 2020 (1)
Oujak 2018 (1)
Veljača 2018 (1)
Siječanj 2018 (1)
Dnevnik.hr
Gol.hr
Zadovoljna.hr
Novaplus.hr
NovaTV.hr
DomaTV.hr
Mojamini.tv