obd2shop

srijeda, 15.02.2023.

How to Clone Tricore ECU with FoxFlash/KT200 Tool?

FoxFlash & KT200 Programmer can support cloning ECU function as OBDSTAR DC706. This is an introduction on how to clone Tricore ECU with new KT200 software step by step. The procedure may apply to FoxFlash software as well.

Step1. Read ECU data via "BOOT MODE TRICORE" or "BENCH TRICORE" option. Including Micro FLASH, EEPROM data from original ECU & new ECU.

Step2. Select Menu >> Select Drive >> TOOL BOOT >> TOOLS BOOT MODE - INFINEON TRICORE Clone Service >> ECU Model

Step3. Fill 1st option with original ECU Micro file, fill 2nd option with new ECU Micro file.

Step4. Click "CLONE & SAVE" to save new ECU file.

Step5. Select BOOT MODE >> INFINION TRICORE Boot >> ECU Model >> Load new ECU file >> Write to new ECU
* BENCH TRICORE may cause incomplete writing of ECU data(Boot is recommended)

Attention
1. Please write the original EEPROM to new ECU with no changes;
2. Please write Micro FLASH & EEPROM data separately, CANNOT read & write together;
3. If the Micro FLASH data cannot be written, it needs to be processed manually with winols. Or asking help for a professional engineer.
4. Nonsupport VW 5th generation IMMO system.

Technical Support
www.obd2shop.co.uk

Oznake: foxflash ecu programmer, kt200 ecu progarmmer, obdstar dc706

15.02.2023. u 07:05 • 0 Komentara • Print • # • ^

ponedjeljak, 26.12.2022.

KT200 ECU Programmer Added Offline Workstation USB

KT200 ECU Programmer Master Version has added a new feature to read & write ECU/TCU via OBD/Bench/Boot/BDM/Jtag offline. Without having to connect to the Internet, just plug the KT200 Offline Workstation USB Dongle to realize. This is very useful for outdoor ECU tuning where the Internet is too weak or not.

The black is the U disk. It contains software and installation instruction, which should be installed online before it can work offline. The white is the dongle to activate the first-time running.

Note:
For KT200 Auto Version, users should upgrade to the full version before buying the offline workstation USB.

KT200 Reads JCB EDC17CV44 Offline on Bench
Open KT200 software >> Select Driver >> BENCH MODE >> JCB >> TC1767-JCB >> EDC17 CV44 >> OK >> Connect
Keep ECU power on. Click "OK".
Read All >> Save
Keep ECU power on. Click "OK".
Reading in progress... wait until 100%.
End of read, turn the dashboard off. Click "OK".
Completed.

KT200 Reads Renault SID310 Offline by OBD
Open KT200 software >> Select Driver >> Car obd >> JCB >> Renault >> Master >> 2.3 dCi SID310 "CAN >> OK

KT200 Reads VW EDC 16U31 Offline on Bench
Open KT200 software >> Select Driver >> BENCH MODE >> Volkswagen >> MPC56 3/4 - VAG >> DIESEL EDC16 U31 >> Connect
Keep ECU power ON. Click "OK".
Read All >> Save
Keep ECU power on. Click "OK".
Reading in progress... wait until 100%.
End of read, turn the dashboard off. Click "OK".
Completed.

www.obd2shop.co.uk

Oznake: kt200 ecu progarmmer

26.12.2022. u 02:41 • 0 Komentara • Print • # • ^

srijeda, 09.11.2022.

KT200 V11.01 Software Free Download & Installation Guide

KT200 ECU Programmer latest software version V11.01 has released, here you can free download & guide to install.

Where to free download KT200 v11.01?
Mega: https://mega.nz/file/NPM0GDZb#PVVHI2mXLekSAiRNd1UvHEom4wLtKcc64isJB7SV6m8
Weiyun: https://share.weiyun.com/T1ZVPy6u (password: zug4hj)
Size: 38.7MB
Compatible system: Win7, Win8/8.1 Win10, Win11.

How to install KT200 v11.01?
Operating video:
https://youtu.be/0Ohi32mexaM

Step1. Click "KT200setup-11.01" package to install software.

Step2. Install & update KT200 driver:
Computer management >> Device manager >> DESKTOP-FSN5GTS >> Other devices >> DFBTech >> Update driver >> Browse my computer for drivers >> Selected "DFBTech_DRIVER" folder >> Next

Step3. Download software & diagram
Start "KT200 Service" >> Download Software
Start downloading software, old version will be completely uninstalled and deleted!
Click "Yes".
Download finished, install or not? If you choose YES, current version will be uninstalled before installation.
Click "Yes".
Yes, I accept the terms of the License Agreement! >> Next >> Next >> Finish
Reset device successfully!

Restart "KT200 Service" >> Download Diagram
Start downloading documents!
Yes >> Finish

Completed.
Now you can start to use Full Version KT200 software.

www.obd2shop.co.uk

Oznake: kt200 ecu progarmmer

09.11.2022. u 15:12 • 0 Komentara • Print • # • ^

utorak, 01.11.2022.

(Solved) KT200 Software V2022.10.01 cannot work

Problem: Recently, some customers reported that when the latest version of KT200 software V2022.10.01 is installed, the gray menu is displayed and cannot be selected and the voltage is not displayed either.

Solution: Uninstall the version 2022.10.01 software, then re-download and install the version 2022.08.20 software.

KT200 V2022.08.20 Download:

https://mega.nz/file/d6YFDD4Z#sIdJrT_V1N7KOQtCBob2feLLj4cH3gZ2yRcMdpEBMrA

Oznake: kt200 ecu progarmmer

01.11.2022. u 10:28 • 0 Komentara • Print • # • ^

srijeda, 12.10.2022.

KT200 10.01 Free Download & ECU Coverage New Update

Here www.obd2shop.co.uk provide the latest version KTM200 10.01 software free download link and ECU supported update content.

Where to free download KT200 10.01
https://mega.nz/file/MKd03YQA#wpv1vARRRYNx9dERkYbIIoPdoaEMrVErVVLRUJYJP4k
Size: 885.6MB
Operating system: Win7, Win8/8.1, Win10, Win11

KTM200 ECU Programmer New Features
lTricore Clone Automatic Function
Added automatism to clone the following control units with OTP zone adaptation and password:
- MED17.5 AUDI
- MED17.5.25 AUDI
- MEVD17.4.2 CITROEN
- EDC17 C08 HYUNDAI
- EDC17 C53 HYUNDAI
- EDC17 C08 KIA
- EDC17 C53 KIA
- EDC17 C66 MERCEDES BENZ
- MEVD17.4.2 PEUGEOT
- MED17.5 SEAT
- MED17.5.25 SEAT
- MED17.5 SKODA
- MED17.5.25 SKODA
- ME17.9.20 SMART
- EDC17 C73 TOYOTA
- MED17.5 VOLKSWAGEN
- MED17.5.25 VOLKSWAGEN

lNew full system for Mercedes truck & CLAAS continental ACM/MCM
Until now, the K-line MCM2 D1/D2 and ACM versions were supported.
Full reading of MCM2.1 D3/D4 and ACM2.1 in CAN line is now also available.

- Reading and writing Micro
- Reading and writing EEPROM
- Recovery
- Checksum

To enable full system communication in D4 hardware versions, it will be necessary to
perform simple unlocking operations with the control unit open by performing bridges on the PCB. At the end it will be possible to close the control unit and read and write all the contents from the pinout.
Follow the instructions in the operating manuals.

lPSA HYBRID4 HV17.4
Bench Mode Per Centraline PSA HYBRID4 HV17.4
Full reading of Citroen/Peugeot HYBRID4 ECUs via pinout added.
The ECU has 2 internal HCUs.
- Reading and writing Micro HCU1 / HCU2
- Reading and writing EEPROM HCU1 / HCU2
- Recovery
- Checksum

lBoot Mode (BAM) for EMS S8 e CRD2
We have added new BOOT MODE (BAM) for complete control unit management on SCANIA:
- CONTINENTAL EMS S8

and new BOOT MODE (BAM) for MERCEDES BENZ / FCA with control units:
- DELPHI CRD2.xx (Versioni SOLENOID e PIEZOTEC)

This makes reading and writing ECU in open mode easier compared to the previous JTAG mode (JTAG function still available). Furthermore, with this method, it's no longer necessary for Delphi CRD2.xx SOLENOIDs to open the ECU from the underside.
- Reading Micro + Eeprom
- Writing Micro + Eeprom
- Recovery
- Checksum

lNew Automatic Function: Tricore Clone
Added automatism to clone the following control units with OTP zone adaptation and password:
- BMW MEVD17.2.8
- BMW MEVD17.2.H
- FIAT DCU17 PC42
- MERCEDES BENZ EDC17 CP10
- MERCEDES DCU17 PC42
- MINI MEVD17.2.8
- MINI MEVD17.2.H
- RENAULT DCU17 PC42
- VOLVO EDC17 CP48

lContinental GPEC2, GPEC3, GPEC4, GPEC4LM !
New BOOT MODE (BAM) for ECUs Continental GPEC fitted on vehicles FCA Fiat, Jeep, Chrysler, Dodge:
- Continental GPEC2A
- Continental GPEC3
- Continental GPEC4
- Continental GPEC4LM
- Reading Micro + Eeprom
- Writing Micro + Eeprom
- Recovery
- Checksum

lCummins CM2200 Dodge Chrysler
Added JTAG MODE for control unit Continental Cummins CM2200 for vehicles Dodge And Chrysler.
- Reading
- Writing
- Recovery
- Checksum

lNew Boot Modes For Delphi DCM7.1 A/B PSA
Boot Mode Solution For Delphi ECU DCM7.1A / DCM7.1B
Added New Boot Mode for micro AURIX TC297 for ECUs DCM7.1A and DCM7.1B mounted on PSA group cars.
- Reading
- Writing
- Recovery
- Checksum

lUpdates for JTAG - Bench - OBD
- New boot via pinout for Mitsubishi Outlander 2.0 Petrol
- Read and write
- Recovery
- Checksum
Added JTAG mode for Adblue ACM Volvo Trucks Euro 6 control unit
- Read
- Writing
- Recovery
- Checksum

Added to the OBD driver for Marelli 9DF FCA also the VIRTUAL reading, in addition to the real reading already present.

lExclusive! - Full System for Marelli 9GF and 8GSW sw version from 2020
- Full System Marelli 9GF for software version from 2020
- Full System Marelli 8GSW for software version from 2020

Added new full system drivers for Marelli 9GF and Marelli 8GSW control units for versions with software update blocked since 2020. On these control units with updated software was no longer allowed the complete reading of micro and eeprom from pinout.

Is now possible: read and write the complete content without opening the control unit.
- Reading and writing Micro
- Reading and writing EEPROM
- Recovery
- Checksum

www.obd2shop.co.uk

Oznake: kt200 ecu progarmmer

12.10.2022. u 09:17 • 0 Komentara • Print • # • ^

<< Arhiva >>