Auto OBD2 tools on Autoobd2.it

Xhorse Dolphin XP005 Cut Toyota TOY40 Emergency Key No Shim

27.03.2024.

Xhorse Dolphin XP-005 has released an upgrade to fix a common problem. That's when cutting the single-sided Toyota emergency key on the M2 clamp with a shim, it'll pop the key out no matter how hard you tighten it. It's super frustrating. Now I'll show how to do it with the M1 clamp, which is mainly used on side cut keys.

Connect VVDI Key Tool Max Pro to the Dolphin machine.
Cut by bitting >> TOY40 >> TOY40 4-4 Bitting
Install the key on the M1 clamp, tip align 3 position.
* Remember to tighten the set screw, make sure it goes no more movement. Otherwise, the key can't be cut right.
Press "OK".

Since I knew the bitting codes, just entered it: 2213, 2421
Cut key >> Continue
Dolphin XP005 will start cutting...
After cutting finish, let's go back to learn the key bitting again.

Find bitting >> Toyota >> TOY40 4-4 Bitting >> OK >> Decode key >> Continue
Learn key success.
Bitting codes are all correct and the same.
Success.

This way saved a lot of time and frustration, especially with breaking bits and ruining emergency valet keys.
Hope this can help.

Xhorse Dolphin + VVDI Key Tool Max Pro Cut TOY40 by Code

27.09.2023.

As you can see, the cylinder is really easy to pop out: 87358, so I don't have to decode them. Next, I'm gonna use Xhorse Dolphin XP005 + Key Tool Max Pro to cut a Toyota TOY40 emergency key by this code. Let's see what will happen.

Cut by bitting >> Toyota >> 87358 >> OK
Install the key blank on M5 clamp B side 2 position as prompted.
The key bitting codes are 4113 and 1412.
Just write them down.
Cut key >> Continue
The Dolphin XP005 failed with an error code: 2, "Not detected probe".
It was asked to do the following steps:
1. Check the clamp is correct.
2. Check height level adjustment finished.
3. Check clamp calibration finished.
4. Check the key insert properly, no chips.

This didn't used to happen. I think this is a result of maybe an update. Remember to keep your Key Tool Max Pro updated to fix the bug.

Let's leave it alone and try another way:
Vehicle database >> Toyota >> TOY40, 4-bittings >> OK >> Enter bitting codes: 4113, 1412 >> Cut key >> Continue
Xhorse Dolphin can complete the cutting this time.

Take out the key to have a test.
It does work.
Done.

Oznake: vvdi key tool max, xhorse dolphin xp005

Xhorse FT-OBD Toyota MINI OBD Tool Uses with Key Tool Max/Max Pro

31.08.2023.

There are two ways to use the Xhorse FT-OBD Toyota MINI OBD Tool:

Method 1: Connect to the mobile APP and use it with the VVDI Mini Key Tool.
Method 2: Connect to the APP of VVDI Key Tool Max/Max Pro and use it with VVDI Key Tool Max/Max Pro.

You may interested:

What Is Xhorse FT-OBD MINI OBD Tool And What Functions Does It Have?
Xhorse Toyota FT-OBD MINI OBD Tool FAQs

This article will introduce you to how the Xhorse FT-OBD Toyota MINI OBD Tool connects and is used with Key Tool Max/Max Pro.

Connect the OBD port of the FT-OBD tool to the car to supply power, then go to the FT-OBD Mini OBD tool home page on the VVDI Key Tool Max/Max Pro.

Click "Select", and the page displays the currently connected devices. Select the correct device to connect.

Click "Device information" in the lower right corner of the Key tool Max/Max Pro, and then click "Combine device" to bind.

Enter the security code, and the association was successful! Click "Refresh" to view the paired device.

Back to the main interface, now you can start using your Toyota MINI OBD FT-OBD Tool!

Oznake: vvdi key tool max, xhorse ft-obd tool

BMW key cut by code using Dolphin XP-005 and Key Tool Max

30.08.2023.

This post will guide you on how to use Dolphin XP-005 and Key Tool Max to cut a BMW key by code.

First, Open the Key Tool Max and select "All Key Lost" >> "BMW".

Then enter your BMW key code as required.

According to the tips, install the M2 clamp and place the blank key as in the picture.

Then select "Cut key" on Key Tool Max to cut the key.

After a few minutes, the cutting is complete.

Then we turn the blank key to the other side to cut and select "Cut Key" again to start.

Cutting key complete!

Oznake: vvdi key tool max, xhorse dolphin xp 005

How to use VVDI Key Tool MAX to unlock Toyota/Lexus Smart Key

06.07.2023.

This post will show you how to use Xhorse VVDI Key Tool Max to unlock Toyota/Lexus smart key. It's great for renewing used or refurbished keys!

Tools you need:
A smart key that has been used in another vehicle
VVDI key tool max

Procedure:

1. Choose "Special Function" in the main menu of the key tool.

2. Scroll down and choose "Unlock Toyota Smart Key".

3. Insert the smart key into the coil, then press "Unlock" to continue.

Unlock Successfully!

So now this could be used in another vehicle.

For more technical services of VVDI Key Tool Max, follow http://blog.xhorse.co.uk/

Oznake: vvdi key tool max

How to cut Ford High Security Key with Dolphin XP-005 and Key Tool MAX

03.07.2023.

This post will show you how to cut Ford High Security remote key by using Xhorse Dolphin XP-005 Key Cutter and VVDI Key Tool MAX.

1. Decode key
Choorse "Find bitting" >> "Ford" >> "HU101 (10 Bitting)"
Clamp Type: M2-A clamp Tip align 1 position
Click "OK", then click "Decode key" to continue.
Learn Key Success.

2. Cut Key
Switch over to the key to be cut
Click "Cut key" on the Key Tool MAX
Cutting key...
Cutting key is completed!
Switch this key over to the other side and cut again.

Done!

www.xhorse.co.uk

Xhorse VVDI Key Tool Max Pro Factory Settings Reset Guide

28.06.2023.

This is a quick guide on resetting Xhorse VVDI Key Tool Max Pro/ VVDI Key Tool Max factory settings. Follow the 3 steps below to learn how to do it.

Step 1. Press the power button once to get the shortcut menu.

Step 2. Long press the blank area in the middle until Key Tool Max Pro automatically reboots. It may take about 22s.

Step 3. Home button >> Settings >> Application >> Xhorse >> Storage space >> clear data/ clear cache

Hope this is helpful.

Contact Info:
Email: Sales01@Xhorse.co.uk
Skype: service@xhorse.co.uk
WhatsApp: +86 15696171957

www.xhorse.co.uk

Oznake: vvdi key tool max pro, vvdi key tool max

Cut a BMW key using Xhorse Key tool Max and Dolphin XP005

19.06.2023.

This post will guide you on cutting a BMW key using Xhorse key tool max and Dolphin XP005 key cutting machine.

The tools we need:
Key Tool Max
Dolphin XP005
BMW Original Key
BMW Blank Key

Here comes the steps:

Step 1. Decode key.
Open the key tool max, choose "Find bitting" >> "BMW" >> "HU92R".

Then we follow the instruction to put the original BMW key into the clamp and choose "Decode Key" to continue.

Learn key success.

Step 2. Cut key.

Extract the original key and insert the key blank to be cut.
Press the "Cut key" on the key tool.

The cutting key has been completed.

Flip it over and do the other side and click "Cut Key" again.
It will go through all the same steps.
The cutting key was completed.

Xhorse VVDI Key Tool Max Recharge BMW Key Battery

13.06.2023.

Xhorse VVDI Key Tool Max/ Key Tool Max Pro can support recharging your BMW key fob battery successfully. Most BMW batteries are rechargeable and soldered to the board. Next, I'm going to demonstrate how to do it.

Special function >> Remote charge battery
Put the rechargeable key into the Key Tool Max coil(such as supporting old-type BMW EWS series modes with rechargeable keys).
Press "Start to charge".

Xhorse Key Tool Max will begin a countdown(You'll notice that it fails if it doesn't detect a key).
So I'm going to let it charge up for a bit and then come back.
...
After we've had it charging for 15 minutes, I'm going to go ahead and stop it.
Press "Stop".
Success.

Go to "Remote clone" to test frequency, and press the key button.
Now the remote is functioning.

Oznake: vvdi key tool max

Xhorse VVDI Key Tool Max Program 2023 GMC Savanna by OBD

30.05.2023.

Today I'll introduce 2 ways that can successfully program the 2023 GMC Savanna with Xhorse VVDI Key Tool Max + Super Chip by OBD. Both can be done in minutes and start the vehicle.

Method 1. Generate Transponder
The 2023 GMC Savanna key is the same as the Chevy Circle ID46 chip. We can use the way in case all keys lost.

Put a Super Chip into the Key Tool Max coil.
Generate transponder >> ID46(PCF7936) >> ID46-Chevrolet Circle >> Generate
Complete.

Method 2. Transponder Clone
In this way, we should have an original working key to clone.

Put the working key into the Key Tool Max slot.
Transponder clone >> Read transponder >> Clone >> Start clone >> 46 Transponder clone >> Original key clone(recommend)

Please put the original car key into the coil for verification.
The password verification succeeds and the decryption succeeds.

Please take out the original key, and suggest putting VVDI super chip or wireless remote.

Write data.
Copy successfully.

Oznake: vvdi key tool max

Residential Key Cutting with Dolphin XP-005 + Key Tool Max

03.05.2023.

This post will show you how to cut residential keys with Xhorse Dolphin XP-005 Key cutting machine and Key Tool Max.

Select "Universal key duplication" >> "Standard single-sided" >> "Shoulder align" >> "M4 clamp", and then we hit the "decode key", so it drags the tracer along the cuts.

Universal key decode success...

Now what we're gonna do is take our key blank and put that into the M4 Clamp.

And click "Cut key" on the key tool to cut the key.

Done!

It's pretty quick and easy.

Technical Support:
https://www.xhorse.co.uk/.uk/

Oznake: vvdi key tool max, xhorse dolphin xp005

Solved: Xhorse VVDI Key Tool MAX Clone ID46 "NOT support this chip"

25.10.2022.

Question: I was using Xhorse VVDI Key Tool MAX Pro to clone a Transponder 46 PCF7941A remote, but it failed when writing data.
It says: "Write failed: NOT support this chip."

What type of remote should I use? Please advise.

Solution
1. XE Series Super Remote
2. VVDI Super Chip
Change to clone either of above options is workable.

Hope this is helpful.

Technical support
www.xhorse.co.uk

Oznake: vvdi key tool max

Xhorse VVDI Key Tool Max Clone Mitsubishi Zinger 315Mhz Key

18.10.2022.

Today I'm gonna show how to clone a Mitsubishi Zinger 315Mhz Remote with Xhorse VVDI Key Tool Max programmer. Easy operation in 3 minutes. I'll use a working key and a new XK Series Wired Remote.

Take out circuit board of new key to connect with Key Tool Max via cable.

Remote clone >> HCS/Fixed code clone >> Automotive

Put the working key into VVDI Key Tool Max coil.

Press "Start clone" and follow the prompts:
Press Lock button.
Press again Lock button.
Press Unlock button.
Press Trunk button.
Press Panic button.

Confirm frequency: 315.03MHz, 421bps.
Press "Clone".
Writing data...
Burn success.

Unplug circuit board to install battery for a try.
It can now successfully lock/unlock the car.
Done.

This should be workable on upgrade version VVDI Key Tool MAX Pro as well.

Oznake: vvdi key tool max

Xhorse VVDI Key Tool Max Clone Mitsubishi Attrage 2018 ID46

04.10.2022.

Xhorse VVDI Key Tool Max can easily clone 2018 Mitsubishi Attrage ID46 key in 2 minutes. Just need an original working key & XT27 Super Chip. Following I'm gonna show how to do.

Put the original key into Key Tool Max coil,
Transponder clone >> Read transponder >> Clone >> Start clone > 46 transponder clone >> Original key clone(recommend)

Insert the original key into ignition.
Hold VVDI Key Tool Max close to ignition switch.
Sniffer data...
Place the working key into coil for verification again.
The password verification succeeds.
The decryption succeeds.

Take out original key to put in a VVDI Super Chip or Wireless Remote instead.
Checking key...
Write data...
Copy successfully.

Insert Super Chip into a new key, it can start the vehicle.
Done.

This is how to clone 2018 Mitsubishi Attrage ID46 key with VVDI Key Tool Max programmer.
www.xhorse.co.uk

Oznake: vvdi key tool max

Xhorse Key Tool Max + MINI OBD Tool Program 2015 Peugeot 208 AKL

27.09.2022.

This is a 2015 Peugeot 208 with all keys lost. Having decoded & cut out the HU83 with Dolphin XP-005 machine, let's go on programming the key. I'll use Xhorse Key Tool Max + MINI OBD Tool to finish the job.

Read PIN Code
Plug Mini OBD Tool into OBD2 interface.
Turn ignition on.
Switch to Mini OBD function page:
Immo programming >> Peugeot >> Password reading >> Type 1 CAN(all key lost or adding) >> Execute >> IMMO password reading

This function will cause wiper to move, which is normal.
Turn on the double flash indicator.
Open then close the driver door once.

The PIN code for this car is: TKNY
Turn on ignition once, then program key.

Program Key
Go back to Select by model >> Start executing >> Key programming
Turn on the ignition switch!
Enter 4-digit password: TKNY

Please complete the following operations within 15s:
Turn off the ignition switch, then turn on the ignition switch!
Press "Confirm" after completing.

Programmed successfully.
Press "Yes" to program next one.
Insert new key and turn on ignition switch!
Programmed successfully.
Press "No" to complete.
VVDI Key Tool Max will display the steps to reprogram, read it if in needed.

Take out the 2 keys, both can perfectly work.
Done.

www.xhorse.co.uk

Xhorse VVDI Key Tool Max Adds Honda Civic FD 2009 Key

19.07.2022.

One customer had lost Honda remote and only have a normal key. So following I'll program a new remote for Honda Civic FD 2009 with Xhorse VVDI Key Tool Max + MINI OBD Tool key programmer.

1. Generate Remote
Plug MINI OBD Tool into OBD, and connect to VVDI Key Tool Max.
Put a XNHO00EN Wireless Remote into key slot, let's start:
Vehicle remote >> Honda >> Civic FD >> Civic FD 433 ID46 2161 >> Generate remote
Burn success.

2. Add a Key
Turn ignition on with working key.
Go to MINI OBD menu.
IMMO programming >> Honda >> Civic >> IMMO system-46(2006-2011) >> Start execution >> Add a key

Turn off ignition switch.
Insert the working key, switch ignition on.
Turn off ignition switch.
Turn on the ignition switch.
If no response within 10s, please turn off/on the ignition again.
Turn off ignition switch.
Insert the new key and switch ignition on within 15s.
Turn off ignition switch.
Switch ignition on.
Turn off ignition switch.
Switch ignition on.

The security light has gone off now. Press "Yes".
Turn off ignition switch.
Switch ignition on.
Program completed.

3. Test Key
New remote can start the car, and remote does work.
Done.

This is how to add Honda Civic FD 2009 key with VVDI Key Tool Max successfully.
www.xhorse.co.uk

Oznake: vvdi key tool max, mini obd tool

>clog.dnevnik.hr/autoobd2/slike/originals/solution-xhorse-wired-remote-burn-failed-on-vvdi-key-tool-max-2.jpg" rel="gallery[1654583883]" target="_blank">

Solution: Xhorse Wired Remote Burn Failed on VVDI Key Tool Max

07.06.2022.

Problem1: I have tried 5 XKB506EN Wire Remotes to generate 5K0-837-202-S chip. The instruction says wired remote is okay, but it always failed and prompted:
"Burn failed. Please put in X wire remote, XN wireless remote or XT superchip-remote."

What's the problem? Isn't the XK series remote workable?

Problem2: I have met same problem when generating Sorento OSLOKA-910T 433 chip with Xhorse VVDI Key Tool Max Programmer. Any ideas? Please help!

Solution
2 tips to be noted when generating XK remotes
1) Put circuit board vertically into coil.
2) Please remove battery, connect XK remote via cable to generate.

Many users are installing the battery on XK Wired Remote to generate, that's why caused failed issue.

Hope this is helpful.

Technical support:
www.xhorse.co.uk

Oznake: vvdi key tool max

Solution: Xhorse VVDI Key Tool Max Calculate Failed Error:9B

17.05.2022.

Problem: I've followed the instructions to program a XM38 Universal Smart Key with Xhorse VVDI Key Tool Max programmer. But it fails all the time, and came out an attention: "Calculate failed(error code: Error:9B), please collect and retry!" Any ideas?

Solution
The reason why caused the issue is because of incorrect version. Please noticed to use same version of VVDI Key Tools & remote keys when programming.

For examples, use a GL version Key Tool Max to program a GL version remote key. In this case, the remote maybe a Chinese version remote. Users should pay attention to buy the correct version of VVDI Remotes.

Another tip to note: Most failed problems are due to wrong key model. Users should follow the instructions to program the correct key model.

In this case, XM38 key model is correct as required. But many users may make the mistake of buying a different model, such as XM28. Since both can program Toyota remotes.

1. How to distinguish XM28 or XM38 remote?
Red arrow: XM28 circuit board has a chip & pins in marked position.
Blue arrow: XM38 circuit board does not.

2. What's different between XM28 & XM38?
XM28 does not support 0410, 0010(A9/AA) chip remote.
XM38 can support all Toyota remotes.

Technical support
www.xhorse.co.uk

Oznake: vvdi remote key, vvdi key tool max

Xhorse VVDI Key Tool Max Clone 2008 Chevy Captiva ID46 Easy

15.03.2022.

Xhorse VVDI Key Tool Max Progammer is supported to add a key for 2008 Chevrolet Captiva by cloning transponder 46. Simple operation, finish in 2 minutes. Only to have the original working key & a new remote.

Procedure
Put the original key into VVDI Key Tool Max slot.
Transponder clone >> Read transponder
It’s an cloneable ID46 key.

Clone >> Start clone >> 46 Transponder clone >> Original key clone

Place Xhorse Key Tool Max nearby vehicle coil, turn ignition on for data collecting...
Put the original key back to Key Tool Max slot again.

The password verification succeeds and the decryption succeeds.

Take out original key, and put into a new wireless remote(or VVDI Super Chip).
Copy successfully.

Try the new key, it can start the vehicle.
Key clone was successful.
Done.

This is how to add a new key for 2008 Chevy Captiva via Xhorse Key Tool Max. You may also like:

How to Read Hyundai/Kia ID46 Pin Code by VVDI Key Tool Max?
http://blog.xhorse.co.uk/how-to-read-hyundai-kia-id46-pin-code-by-vvdi-key-tool-max/

Oznake: vvdi key tool max