Problem: The XHORSE DOLPHIN XP-005 could not decode the original key when I selected the HU100 option. The machine stopped and gave the prompt: "Error code: 2, probe not detected. Please do the following steps:
1. Check the clamp position is correct;
2. Check the key insert properly, no chips"

Solution

The image provided shows that the key is clamped in the wrong groove. Remove the key up to the 1st step as a diagram, and the problem can be solved.



Technical Support
E-mail: Sales01@Xhorse.co.uk
Skype: service@xhorse.co.uk
Whatsapp: +8617308368390

www.xhorse.co.uk

Oznake: dolphin xp005

Xhorse Dolphin XP-005 has released an upgrade to fix a common problem. That's when cutting the single-sided Toyota emergency key on the M2 clamp with a shim, it'll pop the key out no matter how hard you tighten it. It's super frustrating. Now I'll show how to do it with the M1 clamp, which is mainly used on side cut keys.

Connect VVDI Key Tool Max Pro to the Dolphin machine.
Cut by bitting >> TOY40 >> TOY40 4-4 Bitting
Install the key on the M1 clamp, tip align 3 position.
* Remember to tighten the set screw, make sure it goes no more movement. Otherwise, the key can't be cut right.
Press "OK".

Since I knew the bitting codes, just entered it: 2213, 2421
Cut key >> Continue
Dolphin XP005 will start cutting...
After cutting finish, let's go back to learn the key bitting again.






Find bitting >> Toyota >> TOY40 4-4 Bitting >> OK >> Decode key >> Continue
Learn key success.
Bitting codes are all correct and the same.
Success.

This way saved a lot of time and frustration, especially with breaking bits and ruining emergency valet keys.
Hope this can help.



www.xhorse.co.uk

Oznake: vvdi key tool max, dolphin xp005

This post will show you how to cut Ford High Security remote key by using Xhorse Dolphin XP-005 Key Cutter and VVDI Key Tool MAX.

1. Decode key
Choorse "Find bitting" >> "Ford" >> "HU101 (10 Bitting)"
Clamp Type: M2-A clamp Tip align 1 position
Click "OK", then click "Decode key" to continue.
Learn Key Success.

2. Cut Key
Switch over to the key to be cut
Click "Cut key" on the Key Tool MAX
Cutting key...
Cutting key is completed!
Switch this key over to the other side and cut again.







Done!

www.xhorse.co.uk

Oznake: vvdi key tool max, dolphin xp005

This post will guide you on cutting a BMW key using Xhorse key tool max and Dolphin XP005 key cutting machine.

The tools we need:
Key Tool Max
Dolphin XP005
BMW Original Key
BMW Blank Key

Here comes the steps:

Step 1. Decode key.
Open the key tool max, choose "Find bitting" >> "BMW" >> "HU92R".

Then we follow the instruction to put the original BMW key into the clamp and choose "Decode Key" to continue.



Learn key success.

Step 2. Cut key.

Extract the original key and insert the key blank to be cut.
Press the "Cut key" on the key tool.

The cutting key has been completed.

Flip it over and do the other side and click "Cut Key" again.
It will go through all the same steps.
The cutting key was completed.


www.xhorse.co.uk

Oznake: vvdi key tool max, dolphin xp005

This is a 2015 Peugeot 208 with all keys lost. Having decoded & cut out the HU83 with Dolphin XP-005 machine, let's go on programming the key. I'll use Xhorse Key Tool Max + MINI OBD Tool to finish the job.

Read PIN Code
Plug Mini OBD Tool into OBD2 interface.
Turn ignition on.
Switch to Mini OBD function page:
Immo programming >> Peugeot >> Password reading >> Type 1 CAN(all key lost or adding) >> Execute >> IMMO password reading

This function will cause wiper to move, which is normal.
Turn on the double flash indicator.
Open then close the driver door once.

The PIN code for this car is: TKNY
Turn on ignition once, then program key.






Program Key
Go back to Select by model >> Start executing >> Key programming
Turn on the ignition switch!
Enter 4-digit password: TKNY

Please complete the following operations within 15s:
Turn off the ignition switch, then turn on the ignition switch!
Press "Confirm" after completing.

Programmed successfully.
Press "Yes" to program next one.
Insert new key and turn on ignition switch!
Programmed successfully.
Press "No" to complete.
VVDI Key Tool Max will display the steps to reprogram, read it if in needed.

Take out the 2 keys, both can perfectly work.
Done.








www.xhorse.co.uk

Oznake: vvdi key tool max, dolphin xp005