Xhorse XKGHG1EN Masker Garage Remote can support to set frequency, delete code, clone remote, recover data and generate remote. This article is talking about how to check delete codes status, so that we can continue to clone remote.

How to check Delete Code Status?
Before cloning remote, we should check the garage remote status, to make sure remote in deleted code status.
1. Deleted code status: The LED will flash once then go out quickly when keep pressing any button of the garage remote.
2. Delete code operation:
1) Press and hold "Up" & "Down" buttons at the same time, until LED light on. Keep pressing 2 buttons until the LED light off, then release the buttons;
2) Press and hold "Pause", until LED light on then off. Release the button, delete code successfully.

How to do Remote Cloning?
1. Preparation work
1) Please confirm the garage remote has been in deleted code status. If not, please do above delete code operation first.
2)Make sure the garage remote frequency is same as original remote, in case the remote cloning failed or even remote cloning successful, but the working distance is too short to work well.

2. Remote cloning operation
1) Press and hold any one button of Xhorse Garage Remote, this remote will enter cloning mode, LED will flash once then off (keep pressing the button).
2) Press and hold original remote one button (same button as step1). Put the original remote next to Xhorse garage remote. Once the LED light is on, which means current button cloning is successful.
3)Follow the above steps to clone remote all buttons one by one.

Read also:
Xhorse Masker Garage Remote User Manual: Set Frequency

Oznake: Xhorse Masker Garage Remote

Xhorse Masker garage remote has a special design and is easy for customers to use. It supports remote cloning (remote clone from original remote), set frequency, clear code, and data recovery functions. It also supports remote generation for a variety of garage remote brands, frequency edition by VVDI KEY TOOL series devices.

This article will focus on explaining one of Masker Garage Remote's functions to you: set the frequency.

1. Set the frequency situation
There are many different brands of garage door openers on the market, with different manufacturers possibly having different frequencies. If the original remote frequency of the remote control and Xhorse garage is different, it may cause the remote cloning to fail or even the remote cloning to be successful, but the working distance is too short, and the operation is not good. Xhorse garage remote supports a set frequency function (20 frequency points) to ensure the same frequency as the original remote.
2. Set frequency operation

` Enter set frequency mode:
Press and hold the "Lock” and "Pause” buttons at this time, remote LED light on, keep pressing two buttons until the remote LED light is off, then release the buttons.
a Set frequency:
Press the “Up" button, Press once, LED flashes once. For different frequencies with different press times, please refer to the frequency reference table.
b Double check frequency:
After the set frequency is successful, release all the buttons. Wait 5 seconds, the remote LED will flash, and the flashing times depend on the set frequency. (Please refer to frequency reference table).

c Exit set frequency mode:
After the remote LED stops flashing, press the “Lock" and “Pause" buttons immediately, meanwhile the LED light is on, and keep pressing 2 buttons until the LED light is off. then release the button and set the frequency operation successfully.

3. Frequency edition by device
If the remote frequency is not in the frequency reference table, VVDI KEY TOOL series device (VVDI KEY TOOL, VVDI MINI KEY TOOL, KEY TOOL MAX, or KEY TOOL PLUS) support to set frequency at random point.
For example: use KEY TOOL MAX cloning 320.5MHz original remote
Take KEY TOOL MAX as an example, copy 320.5MHz garage remote, and the operation steps are as follows:

3.1. Enter Key Tool Max HCS/Fixed code Clone interface and select 320 frequency range.

3.2. Press the button of the original remote according to the device prompts.

3.3. Edit the frequency that required.

3.4. Cloning the data. (If the original remote and cloning remote function code chasing occurred, it can be solved by programming remote after the rolling code ID regeneration).

For more technical services of Masker garage remote, please follow http://blog.xhorse.co.uk/

Oznake: Xhorse Masker Garage Remote